2015 Dodge Ram Key Fob Stuck in Ignition

The usual and common problem often becoming a nightmare for drivers is a 2015 Dodge Ram key fob stuck in the ignition.

Don’t worry though, because it can be fixed easily with the right steps!

In this article, I’ll go over some tips on how to get that pesky key fob out safely without any damage.

It might sound intimidating at first but trust me – removing a stuck key fob from the ignition isn’t as hard as it seems.

Contents

Causes of 2015 Dodge Ram Key Fob Stuck in Ignition

I’ve been working as a car ignition expert for many years, so I’m well-versed in diagnosing issues such as these.

When it comes to when your Dodge Ram key fob is stuck in the ignition, there are several potential causes that need to be analyzed before we can figure out the best course of action.

2015 Dodge Ram key fob stuck in ignition - Infographic

Possible Causes	Explanation
1. Dead battery	The battery in the key fob is dead, causing it to be unable to communicate with the ignition system and get stuck.
2. Faulty ignition switch	The ignition switch is faulty or worn out, preventing it from properly releasing the key fob when attempting to remove it.
3. Broken or damaged a key fob	The key fob is damaged or broken, preventing it from communicating with the ignition system and getting stuck.
4. Mechanical problems	There are mechanical problems with the ignition system, such as worn-out pins or tumblers, causing the key to get stuck.
5. Electrical problems	There are electrical problems with the ignition system, such as a blown fuse or faulty wiring.

Solutions to Get 2015 Dodge Ram Key Fob Out of Ignition

Now that we have discussed the reasons for the 2015 Dodge Ram key fob sticking in the ignition, let us have a look at the solutions.

The following table provides a list of solutions.

Possible Solutions	Explanation
1. Check the battery	Replace the battery in the key fob to see if it will resolve the issue of the key fob not communicating with the ignition system.
2. Jiggle the key	Try gently jiggling the key while turning it to see if it will release from the ignition due to a misalignment.
3. Check the shift lever	Ensure the vehicle is in park or neutral before attempting to remove the key. Incorrect positioning of the shift lever can prevent release.
4. Check the ignition switch	A faulty ignition switch may need to be repaired or replaced by a qualified mechanic.
5. Replace the key fob	If the key fob is damaged or broken, it may need to be replaced.

Non-Invasive Methods to the Key Fob Unstuck

When your key fob is stuck in the ignition of your 2015 Dodge Ram, there are a few non-invasive methods as well that you can try to remove it.

Non-invasive methods mean avoiding damaging the ignition system by not using screwdrivers or hammers to pry open the lock.

These methods involve using everyday household items and do not require any special tools.

Method	Description
Method 1: Try Turning the Steering Wheel	If the key fob is stuck in the ignition due to the steering wheel being locked in place, try turning the steering wheel back and forth while gently wiggling the key fob. This may release the key fob from the ignition.
Method 2: Use a Lubricant	Apply a small amount of graphite powder or similar lubricant to the key fob and gently jiggle it back and forth while pulling it out of the ignition. This can help release the key fob if it’s stuck due to a minor mechanical issue or debris in the ignition.
Method 3: Use a Pair of Pliers	If the key fob is stuck in the ignition due to a mechanical issue, try using a pair of pliers to gently pull it out. It’s important to wrap the pliers with a soft cloth or paper towel to avoid damaging the key fob or ignition. This method should only be used as a last resort and with caution, as it can cause damage to the ignition or key fob.

Explore More:

How to Replace Faulty Ignition Switch in 2015 Dodge Ram

Replacing a faulty ignition switch in a 2015 Dodge Ram requires careful attention to detail and basic knowledge of car mechanics.

Here are the steps involved in replacing a faulty ignition switch in a 2015 Dodge Ram:

Steps	Description
Step 1: Disconnect the Battery	Disconnect the negative cable from the battery to prevent electrical shock or damage.
Step 2: Remove the Steering Column Cover	Use a screwdriver to remove the screws holding the steering column cover in place. Carefully remove the cover and set it aside.
Step 3: Locate the Ignition Switch	Locate the ignition switch under the steering column. It should be mounted to the steering column by two or three screws.
Step 4: Disconnect the Electrical Connections	Disconnect the electrical connections to the ignition switch. Label each wire before disconnecting to ensure proper reconnection.
Step 5: Remove the Ignition Switch	Use a screwdriver to remove the screws holding the ignition switch in place. Once the screws are removed, carefully remove the ignition switch.
Step 6: Install the New Ignition Switch	Install the new ignition switch in the same location as the old one. Secure the new switch in place with screws from the old switch.
Step 7: Reconnect the Electrical Connections	Reconnect the electrical connections to the new ignition switch in the same order they were disconnected. Double-check the labels to ensure proper reconnection.
Step 8: Test the New Ignition Switch	Reconnect the battery and test the new ignition switch by turning the key to the “on” position and ensuring all electrical components are functioning properly.
Step 9: Replace the Steering Column Cover	Replace the steering column cover by securing it with the screws that were removed in Step 2.

Applying Lubricants

Lubrication is one of the effective methods to get the key fob out of ignition.

For your better understanding, I have mentioned the usefulness of the lubricant.

Type of lubricant	Description	Application
Graphite-based powder or spray	Effective for removing sticky residue or corrosion from components without leaving behind any traces. Can also loosen up stiff parts such as tumblers and pins within the lock cylinder, making them easier to move back and forth.	Sprinkle the powder around the ignition switch area and use a toothpick to spread it evenly throughout the opening if necessary. Alternatively, apply a spray by aiming it at the ignition switch area.

Explore More:

Seeking Professional Help

If your Dodge Ram key fob is stuck in the ignition, you may need to seek professional help. When looking for help with this problem, getting advice from someone who knows their way around a car ignition is essential.

You should check out reviews left behind by previous customers so that you’re sure they are reputable before committing to any services they offer.

The best professionals will likely not only provide a solution to your current issue but also give helpful tips on how to prevent future issues with your car’s keys and ignition system.

Conclusion

In conclusion, if your 2015 Dodge Ram key fob is stuck in the ignition, it can be a frustrating issue to deal with.

As an experienced car ignition expert and mechanic, I recommend you first assess the situation to determine how severe the problem is before attempting any non-invasive methods or applying lubricants.

If those don’t work, then use the right tools for the job in order to safely remove it from the ignition.

If all else fails, seek professional help so that this issue won’t become more of a hassle than it needs to be.

My years of experience have taught me that it’s always best to take action as soon as possible when dealing with car issues such as these.

2015 Dodge Ram Key Fob Stuck in Ignition – Ultimate Guide